This is the COMPLETE system kit for a 16-row planter applying a high-rate product.
The OnSite FMS+ 8-channel FlowBoards come complete with everything you need, including all the flowmeters, OnSite FMS+ Module, manifold, and internal plumbing.
Easy Bluetooth Connectivity
This OnSite FMS+ kit includes the popular Bluetooth module for connecting the planter to the in-cab display. This eliminates running a cable from the planter to the cab. The Bluetooth module connects directly to an OnSite Module on the planter and transmits all the flow data for each row back to the cab. The included OnSite Module Cable connects the OnSite module to the Bluetooth Module. Bluetooth makes installation simple. On FlowBoard systems the Bluetooth module should come attached to the back of FlowBoard 1 next to the OnSite Module.
This kit also includes the Module Power Cable. It will connect from any 12V power source on the planter to the OnSite FMS Module, powering the whole system on the planter side. In wired systems, the power is run back from the tractor to the planter, but Bluetooth eliminates this cable, so we just have to get power locally from the planter itself.
This board is designed for products that need a fairly high application rate. Most in-furrow applications will be better served by using our standard 1/4″ flowmeters due to their performance at lower flow rates.
· Each 3/8″ high-flow flowmeter has a flow rate between 0.21 – 2.0 GPM per row. (8.316 GPA – 79.2 GPA at 5MPH and 30″ spacing)
· 1/4″ standard flowmeter boards are available (217-01-16r25b) and have a flow rate of 0.08 – 0.5 GPM per row. (3.168 GPA – 19.8 GPA at 5 MPH and 30″ spacing)
Choose the flowmeter that best fits your desired application rate & speed. Use the formulas below to figure out the right size for you.
GPA = (GPM x 5,940) / (MPH x W)
GPM = (GPA x MPH x W) / (5,940)
· GPA = Gallons Per Acre
· GPM = Gallons Per Minute
· 5,940 = Constant for this Formula
· MPH = Speed You Will Be Traveling
· W = Nozzle Spacing in Inches
The big 7″ touchscreen display is the real brains of the OnSite FMS+ system. It takes the flow meter readings compiled by the OnSite Modules and converts the data to an easy-to-understand bar graph that gives you real-time monitoring of how each row is performing. You will see at a glance how each row is performing and see trends (otherwise known as blockages) as they develop.
Set your target application rates in the OnSite software and it will give you a reference line right on the display so you can see exactly how accurately each row is performing. If OnSite detects any row falling out of the acceptable range, it will change the color of the row and give you an alert. (Alerts can also be silenced.)
If you are running section control, just map the sections to your rows using the easy-to-use section wizard in the software. OnSite Smart Sense will automatically detect when sections are shut off and not trigger alerts.
Software Setup is easy. OnSite Smart Sense will automatically connect to all the OnSite Modules on the planter and put them in the right order. Configuration is largely automated. Just make a few quick choices to tell the software how you want to run. Most OnSiteFMS+ systems can be configured and ready to plant in under 15 minutes.
The OnSite Harness Terminator
The OnSite Terminator tells the system that there are no more modules to connect to. The first OnSite Module connects to the Module Power Cable and the last OnSite Module gets the terminator on the end. Everything in the middle connects with Module-to-Module cables. The whole system is wired in a simple daisy chain configuration, leaving little possibility of hooking anything up wrong.
The terminator comes with a jumper plug already installed. If you would like to use a lift switch, unplug the jumper and plug the lift switch into that port. BENCO has push button lift switch kits available with brackets designed to fit almost any planter on the market.
Kit Includes:
Two 8-row FlowBoards
Two 8-row OnSite FMS+ Modules
Sixteen 1/4″ flowmeters mounted to the FlowBoard
Single section, 16-row manifold with 1″ Female Pipe Thread inlet
Comes plumbed from the manifold to the flowmeters.
OnSite Bluetooth Module for communicating between the planter and the monitor
Display kit
– 7″ touchscreen monitor
– Monitor cradle
– RAM Mount with extension arm
– Power Harness for the monitor (cab side)
OnSite terminator plug
Module Power Harness (planter side)
OnSite Module Harness
One OnSite Module-to-Module Harness to connect FlowBoards together
Two FlowBoard stand with U-brackets and hardware
All necessary brackets, hardware and wiring
This kit does not include: Tanks, pumps, hoses, or fittings going into or out of the FlowBoard. Nor any check valves, P2P brackets, drop tubes or any hardware on the row units themselves. However, all of the above is available separately from BENCO Products. Give us a call at 605-213-1010 to create a complete liquid handling solution for your planter or strip till machine.
$4,850.00
A detailed answer to provide information about your business, build trust with potential customers, or help the visitor with a problem they may be encountering
A detailed answer to provide information about your business, build trust with potential customers, or help the visitor with a problem they may be encountering
A detailed answer to provide information about your business, build trust with potential customers, or help the visitor with a problem they may be encountering
A detailed answer to provide information about your business, build trust with potential customers, or help the visitor with a problem they may be encountering
A detailed answer to provide information about your business, build trust with potential customers, or help the visitor with a problem they may be encountering
A detailed answer to provide information about your business, build trust with potential customers, or help the visitor with a problem they may be encountering
A detailed answer to provide information about your business, build trust with potential customers, or help the visitor with a problem they may be encountering
A detailed answer to provide information about your business, build trust with potential customers, or help the visitor with a problem they may be encountering
BENCO Manufacturing produces industrial quality sprayers, tank trailers, tank stands, 12V motor controls, and agricultural liquid handling components for planters and sprayers. BENCO Manufacturing is a division of BENCO Products, Inc. Privacy Policy | Terms and Return Policy
THIS WEBSITE IS UNDER CONSTRUCTION
Please bear with us as we work to make a better web experience for all of our BENCO customers, including a full product catalog and interactive custom sprayer builders. Any information you find on this site should be accurate, but is not guaranteed. Please call 605-213-1010 to place an order. Thanks for your patience. Dismiss